RAMCO HILUX

India's best rated Boards & Tiles for Wall, Ceiling, Panel Systems. It introduced the innovative Calcium Silicate Board, a versatile building material, using Japanese technology from the ASK Corporation, Japan.Dealer,Manufacturer,India,producers

Dry Wall Solution      >>       JOINTING & FINISHING
  • PARTITIONS
  • FIRE RATED PARTITION
  • Two Hour Partition
  • METAL FRAMED PARTITIONS
  • One Hour Partition Four Hour Partition
    Single Layer Partition One and Half Hour Partition
  • ALUMINIUM STUD PARTITION
  • Partition with CSB Fillets Two Hour Partition
  • TIMBER STUD PARTITION
  • Double Layer Partition
  • FIRE RATED HIGH WALLS
  • WALL LININGS
  • One Hour Partition
  • JOINTING & FINISHING
  • JOINTING & FINISHING

    Hilux Calcium Silicate Boards are available with Tapered and Square edges. The joints of these boards can be jointed & finished by using specially formulated jointing compound and fibre tape, to get seamless finish. The square edges of the boards can be made tapered (40 x 1.5 mm) at site by using grinding machine or by chamfering the edges (4 x 3 mm). The corners can also be reinforced with fiber tape. The procedure is detailed below :

    Step -1(First-coat)
    • Apply Jointing compound at joint
    • Firmly embed the 48 mm wide self adhesive fiber tape centrally into the joint
    • Apply jointing compound on the fibre tape with tapping knife
    • Use sufficient pressure to ensure that the tape is firmly placed
    • The tape should be free from trapped air/bubbles and this application should be approximately 4" wide
    • Remove extra material lying out side of the joint and allow it to dry
    Step 2 (Second coat)
    • When the first coat has dried, apply second coat of jointing compound to the joint
    • Ensure that the preceding application and tape is completely covered by making this application wider than the earlier( 6" )
    • Remove extra material and allow it to dry
    Step 3 (Third coat- finishing coat)
    • When the second coat has dried, apply a very thin layer of jointing compound to the joint
    • Ensure that the preceding application and tape is completely covered by making this application wider than the earlier and spread it, to remove visibility of the joint( 8" )
    • Feather out joint edges to remove extra material and allow it to dry

    Square Edge Joints:

    Step -1
    • Fill the groove formed by trimmed edges with jointing compound & leave it to dry
    • Firmly stick the 48 mm wide self adhesive fiber tape centrally onto the joint
    • Apply jointing compound on the fibre tape with tapping knife
    • Use sufficient pressure to ensure that the tape is firmly placed
    • The tape should be free from trapped air/bubbles and this application should be approximately 6" wide
    • Remove extra material lying out side of the joint and allow it to dry
    Step - 2
    • Apply a thin layer of jointing compound over the previous application keeping it 8" wide
    • Remove extra material lying out side of the joint and allow it to dry
    Step 3
    • Apply a thin layer of jointing compound over the previous application keeping it 12" wide
    • Remove extra material lying out side of the joint and allow it to dry
    • Make sure that the width of the joints should be as wide as described above the narrow finished joints will be more visible than the wider one
    Internal & External corner joints
    • Fibre tape should be used by folding it from its centre making it in angle shape (24 x 24 mm) to accommodate both sides of the corners. This folded tape is embedded at corners by using jointing compound as described above
    • Two more coats of compound are applied over it to avoid visibility
    Nail/Screw Finishing
    • Nail screw heads should be just below the surface of the board and should not be driven too deep
    • All nail/screw heads are to be covered with the jointing compound twice to achieve the right finished surface
    NOTE
    • It is recommended that the square edges of the boards should be made tapered (40 x 1.5 mm) at site to achieve good results instead of forming "V" groove
    • Please make sure the screws are sufficiently & properly driven and there is no movement between the board and steel section, before starting jointing & finishing
    • Please make sure that sufficient jointing compound is applied between the board surface and the tape. Please do not depend on the adhesive used with the fibre tape to make it self adhesive, because it may not be sufficient to hold the tape with the board surface
    RAMCO HILUX
    Downloads
    Clean Room Brochure
    Board Brochure
    Tile Brochure
    FireBook
    Sound Book
    Water Book
    RAMCO HILUX
    RAMCO HILUX
    2016 © Ramco Industries Limited