RAMCO HILUX

India's best rated Boards & Tiles for Wall, Ceiling, Panel Systems. It introduced the innovative Calcium Silicate Board, a versatile building material, using Japanese technology from the ASK Corporation, Japan.Dealer,Manufacturer,India,producers

Dry Wall Solution      >>       INSTALLATION
  • PARTITIONS
  • FIRE RATED PARTITION
  • Two Hour Partition
  • METAL FRAMED PARTITIONS
  • One Hour Partition Four Hour Partition
    Single Layer Partition One and Half Hour Partition
  • ALUMINIUM STUD PARTITION
  • Partition with CSB Fillets Two Hour Partition
  • TIMBER STUD PARTITION
  • Double Layer Partition
  • FIRE RATED HIGH WALLS
  • WALL LININGS
  • One Hour Partition
  • JOINTING & FINISHING
  • Metal Framed Partitions (Single Layer Partitions)

    Hilux metal framed, non-load bearing partitions are assembled at site, using Calcium Silicate Boards, screw fixed to either side of light weight cold rolled galvanized steel studs, which are placed vertically into the floor and ceiling channel, at 610 mm centres and are suitable for any type of decoration after filling and finishing of the joints. The system provides good fire resistance, sound and thermal insulation properties. The system has in-built provisions for concealed electrical & plumbing services because of cut-outs made in the web of studs.

    PERFORMANCE

    System Thickness66 mm70 mm74 mm
    Fire ResistanceNon-fire ratedNon-fire ratedNon-fire rated
    Sound Insulation39 dB39 dB40 mm
    Height2440 mm2700 mm3000 mm

    INSTALLATION

    Frame Work

    Floor & ceiling channel is screw fixed to the floor with the help of nylon sleeves and wood screws at 450 mm centres. Another same channel is then fixed to the soffit, making it plumb to the floor channel in the same manner. The studs, cut 5 mm shorter, are placed vertically into the floor and ceiling channel at 610 mm centres. The cut-outs of the studs are kept in a line to accommodate services. Intermediate channel is also fixed horizontally if the partition height exceeds the board length on both sides of stud. Necessary metal or wood batons are also incorporated to accept load of any material like cupboard etc. at this stage only.

    Board Fixing

    Tapered edge Hilux Calcium Silicate Boards are screw fixed to either side of stud and channel by self drilling & taping screws having Phillips head with under head cutter, of suitable length (10 mm + thickness of the board) at 200 mm centres, keeping 12 mm away from the edges and 40 mm from the corners. A gap of 1.5 - 2 mm is also provided between the boards. The boards are chamfered at square edges by 4 x 3 mm, or made tapered (40 x 1.5 mm)at site, by grinding them, before fixing. The joints are staggered to avoid through passage to achieve performance levels.

    Jointing & Finishing

    Hilux Calcium Silicate Boards joints are finished with specially formulated jointing compound and 48 mm wide fiber tape to get seamless finish.

    Details

    Hilux Board8 mm/ 10 mm/ 12 mm ThickOne layer board on each side of studs & channel
    Floor / Ceiling Channel50 x 32 x 32 x 0.55 mmTop and bottom Perimeter of the partition
    Stud48 x 50 x 48 x 0.55 mmVertically at 610 mm c/c
    Intermediate Member45 x 15 x 15 x 0.9 mmAt horizontal board joint
    Screws (Phillips head)25 mm long, self drilling with under head cutter12 mm from the edge & 40 mm from the corner of the board at 200 mm c/c

    RAMCO HILUX
    Downloads
    Clean Room Brochure
    Board Brochure
    Tile Brochure
    FireBook
    Sound Book
    Water Book
    RAMCO HILUX
    RAMCO HILUX
    2016 © Ramco Industries Limited